RX600R-15Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The -1.5 1mm wheel was designed so we could use wider tires up front of our RX28s, while keeping the width up front with the equivalent of a +1 with 8.5mm wheels (in terms of the RX28). The negative offset- inset design reduces the scrub radius and makes the steering more precise. When using 11mm tires up front, we have found that the car is easier to drive and more consistent in modified, with smoother response and longer lasting tire life.

RX600R-15W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The -1.5 1mm wheel was designed so we could use wider tires up front of our RX28s, while keeping the width up front with the equivalent of a +1 with 8.5mm wheels (in terms of the RX28). The negative offset- inset design reduces the scrub radius and makes the steering more precise. When using 11mm tires up front, we have found that the car is easier to drive and more consistent in modified, with smoother response and longer lasting tire life.

RX600R-15G

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The -1.5 1mm wheel was designed so we could use wider tires up front of our RX28s, while keeping the width up front with the equivalent of a +1 with 8.5mm wheels (in terms of the RX28). The negative offset- inset design reduces the scrub radius and makes the steering more precise. When using 11mm tires up front, we have found that the car is easier to drive and more consistent in modified, with smoother response and longer lasting tire life.

RX507

This suspension is inspired by our RX505 Kit for the GLR GT.

Why did we do this? Well, there was 3 main reasons:

1.The spring set up on the MRZ leaves a lot to be desired. It is very hard to change springs, the springs are too far out on the car, which make the available rates unusable in high bite conditions. Our spring set up is easier to use, has a wider tuning window and uses linear cylinder shape springs. The car steers more, is smoother and overall faster around a track with this set up.

2.The battery cradle on the MRZ is a PITA. Our simple rubber band set up is much easier to use, and it effectively lowers the Center of Gravity on the MRZ. This translates into better performance with less traction rolling and more corner speed.

3.Lighter weight. The new parts shed some of the weight on the MRZ. it's not a massive difference, but everything helps on a pretty heavy kit out of the box.

As an added benefit, the rear cradle is designed to be able to be used with GL Side Links for quicker steering response and also allows the option of running the standar or long length dampers.

RX518

Based off of our 2021 and 2022 PN and 2021GL National winning RX505 this rear suspension is designed to increase the performance of your GL Racing GLR. Comes with all new V2 Side springs for more fine tuning.

This suspension lowers the CG of the car and provides better forward bite and faster, flatter cornering.

RX514

All New for Reflex is the GL Racing GLR Chassis. More forward weight bias for better stability and less traction rolling. Black slick coating and chamfered edges for less friction on the track when bottoming out and rolling on RCP.

RX515

What makes the Reflex Ball Diff Special? Attention to details. We worked on sourcing the highest quality materials and ended up with a really light weight ball diff that has better engagement and acceleration.

The ball diff comes standard with super hard steel diff rings, 7075 T6 aluminum diff shaft, carbide diff balls, soft o-ring for finer adjustment, our specially designed 9 ball spur gear and ultra lightweight aluminum diff parts.

RX513

RX512

Designed to increase stabilty, keep the car flatter and make it more consistent over a full run. We achieve this by moving the weight bias of the car further forward by scalloping the battery area and making the front section wider.

We also have finished the chassis in a slick, black coating with laswr engraved reflex logo and have chamfered the edges of the contact areas to reduce friction and make the chassis really pop.

RX505-1

RX506

RX505X

EVERYTHING YOU NEED TO CONVERT YOUR GLR-GT TO THE RX505 REAR END IN 1 PACKAGE.

NICE & EASY!

INCLUDED IN PACKAGE-

1 - REFLEX RX505 CONVERSION KIT

1 - GL-S005 - GLR SHOCK BODY TREE (GLR SIDE SHOCKS (2 PCS) NEEDED TO COMPLETE)

1 - GLR-6174 - GLR METAL SHOCK PISTONS (2 PCS NEEDED TO COMPLETE)

1 - GL-GT-029 - GLR-GT 3.5MM BALL JOINTS (2 PCS NEEDED TO COMPLETE)

1 - GLR-S021 - GLR 3.5MM BALL JOINT HEADS (2 PCS NEEDED TO COMPLETE)

RX505

***Please note. You will need the following items to complete conversion***

1 - GLR Side Dampers (GLR-S005)

1 - GLR Metal Piston for Side Damper (GLR-18-6174)

1 - 3.5mm Ball Joint Heads (2pcs) GLR-GT-S-029 or GLF-S-026

1 - 3.5mm Ball Joints (2pcs) GLR-S021

This is the ultimate hop up for your GL Racing RGT! If you were to buy any upgrades for your RGT, we would say this rear end, some PN Side Shocks (used as damper tubes) and some spring sets would be all that would be needed to win any race you enter, at any level.

Developed in house to make your GL RGT simply faster. This rear end emulates larger scale pan cars with vertical side springs, o ring battery mount and a more angled shock adjustment possibility. This rear end drops the CG of the car further, provides better traction and drive out of the corners than the side shock or the standard set up. The handling is more precise and consistent with better grip, flatter cornering, less traction rolling, more rotation, more forward and side bite all, while making the car MUCH EASIER TO DRIVE.

People that have tested this rear end insist that the car is far more dynamic and simply "unfair" to the competition.

NOTES:

-Rear end includes all the hardware necessary to install in your RGT, with the exception of side dampers/shocks and mounting hardware for those. We recommend the PN racing ones for cost and ease of use. (If using PN Dampers, we recommend to drill a 1mm hole in the shock body towards the top of the threaded body for venting).

-The rear end is designed to work with the shorter shock shaft on your RGT. If you have the aftermarket shock, swap the shaft with the stock one or cut the longer one about 2-3mm. Adjust droop and pre-load normally. Use Short Springs.

TIPS:

-Angle your center shock downwards for more aggressive response.

-Flatten the center shock for smoother response

-Raising the outer pivot on the side tubes gives more body roll and smoother response but more rotation

-Softer side spring creates less side bite and helps in high bite to prevent traction roll. Makes the car have more rotation on power in lower bite, but makes the car easier to drive in high bite. Harder springs have the opposite effect.

-Start with 5-10k in lower bite on the PN Side tubes 15k to start in higher bite

-Start with 15k in GLR Side Tubes in lower bite, 30k in higher bite.

-The side spring holes are pre-theaded. However, if you side springs are tough to adjust, use one of the provided M2 screws to free up the threads a bit. Using a little diff grease can also help when tight.

RX504

RX503

RX502

This is the all new GL RGT Rear Geometry Conversion Kit. Developed in house this kit was designed with our numerous years of experience designing 1/12 and 1/10 Pan Cars. The shock mounting postions and angles have been revised, the center of gravity has been dropped and the parts count and complexity have been reduced considerably. Additionally the integrated rear body mount position is compatible with most lexan bodies we have tested. The results are a car that produces more rear grip, better steering and more consistent, predictable handling. Having removed the motor mount shock mount extension also allows for easier wire routing for smoother pod movement and better airflow for the motor to stay cool.

Lap time wise we have seen resonable improvement, and consistency has gone through the roof! The car is much more composed under power and tracks far straighter. As another benefit, the time in between rear damper maintenance has been increased.

This kit includes the rear cross brace the aluminum tri mount to be installed on the stock motor mount. It is compatible with both the GL GLR rear shocks and PN Racing Side Shocks.

Needed to Complete:

-When using GLR Parts:

*GLR-S005 Plastic Shocks

*GLR-S016 Alloy Adjusters

*GLR-S021 Pivot Balls

*2 x M2 x 4mm BH Screws

*2 x M2 x 6mm Set Screws

*GLR-003-S Spring Set

(*alternatively, using Atomic 3.5mm Ball Studs simplifies the parts count AMZ-OP023, use 4 pcs of these plus 2x M2 nuts)

-When Using PN Racing Parts

*MR2162A Spring Set

*MR2990

*4 x M2 x 8mm BH Machine Screws

*2 x M2 Nut

RX28SE-03

RX28SE-07