GL-FO-S-028

GL-FO-S-006

GL-FO-OP-002

AC007-A

AC002-K

GL-RX-BOX

Reedy Power

2mm Bullet Adapter (2)

This part fits the following other parts

• #27201 - Reedy 324-S Compact Balance Charger
• #27244 - 2S Parallel Charging Board w/2mm Bullet Adapter

The Sonic 1525 is designed specifically for 1:28 and other micro vehicles intended for competition use. Thanks to input from our racing team and customers, the Reedy development team has created reliable, yet powerful design featuring the latest brushless motor technology along with the engineering experience that is responsible for 30 World Championship titles.

This part fits the following vehicles

• RC28 Team 
• RC28R Team 
• RC10 Model 24 Classic

RX28-045-1

Version 2 molded A-Arms for your RX28.

This set includes:

-2 x Upper Arms (Black/Medium)

-2 x Lower Arms (Black/Medium)

Gen 3 springs.  They are shorter than previous side springs, but are compatible across platforms.

The V2 Wing Things are designed to make mounting your wing much easier.  Install the screw from the bottom of the body and thread them into the wing thing threads.  You can hold the wing thing with a 4.0mm hex wrench to fully tighten.  Lighter and smaller than the V1 Set!

Blue

The V2 Wing Things are designed to make mounting your wing much easier.  Install the screw from the bottom of the body and thread them into the wing thing threads.  You can hold the wing thing with a 4.0mm hex wrench to fully tighten.  Lighter and smaller than the V1 Set!

RX532-BK

The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.

The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.

RX532BL

The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.

The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.

RX605-40

All new from Reflex Racing is our brand new Low Profile slick tires for RCP tracks. These tires are made from a very tough and long lasting grippy rubber. They were developed to match the grip envelope of our 30 degree radials.

We recommend to mount the tires 1 of 2 ways:

For a less hassle, no truing method, mount on a Reflex Racing Speed Dish Wheel with a 22.6 plate. Let the tire break in over time. It is very long lasting, but the results are that the tire works after a couple of laps. If it is too aggressive in the middle of the corner, try removing some camber or running a softer front spring.

If you like to true your tires, mount them up on a truer and bring them down to 22.7-22.8mm and use with a 22.6 plate. After truing, the tires may be a little bit aggressive while they break in, so make sure you have some freshly skimmed 30 degree rear radials or you may have too much front bite. Since the material is very hard, we recommend running the tire truer where the tire and drum are spinning away from each other. With the PN Brand of truers, we find the most success running the truer in reverse and around 6v.

So when do you chose the 45 vs the 40? The 40 cuts a little bit harder, but it is smoother in the middle of the corner. Opposite is true for the 45. It really depends on what you are trying to do. If you want more middle and exit, use the 45. If you want smoother middle and exit, use the 40.

***Wheels are for picture only, they are not included***

RX605-45

All new from Reflex Racing is our brand new Low Profile slick tires for RCP tracks. These tires are made from a very tough and long lasting grippy rubber. They were developed to match the grip envelope of our 30 degree radials.

We recommend to mount the tires 1 of 2 ways:

For a less hassle, no truing method, mount on a Reflex Racing Speed Dish Wheel with a 22.6 plate. Let the tire break in over time. It is very long lasting, but the results are that the tire works after a couple of laps. If it is too aggressive in the middle of the corner, try removing some camber or running a softer front spring.

If you like to true your tires, mount them up on a truer and bring them down to 22.7-22.8mm and use with a 22.6 plate. After truing, the tires may be a little bit aggressive while they break in, so make sure you have some freshly skimmed 30 degree rear radials or you may have too much front bite. Since the material is very hard, we recommend running the tire truer where the tire and drum are spinning away from each other. With the PN Brand of truers, we find the most success running the truer in reverse and around 6v.

So when do you chose the 45 vs the 40? The 40 cuts a little bit harder, but it is smoother in the middle of the corner. Opposite is true for the 45. It really depends on what you are trying to do. If you want more middle and exit, use the 45. If you want smoother middle and exit, use the 40.

***Wheels are for picture only, they are not included***