RX28-046-1

Version 2 molded A-Arms for your RX28. These are the hard arms. Hard arms are better for higher bite conditions as they provide sharper mid corner steering while reducing traction rolling.

This set includes:

-2 x Upper Arms (Gray/Hard)

-2 x Lower Arms (Gray/Hard)

RX28A-30

Go longer between re-builds with these dust covers for your ball diff. Compatible only with the Reflex Racing V3 Spurs and beyond, these dust covers should work on the majority of diffs out there when using a Version 3 and beyond ball diff spur.

The covers add about 1.6g of weight to your diff.

RX28A-39

All New RX28 Steel Chassis for your RX28G2 Plate Cars. This new chassis allow for fore and aft movement of 20mm wide batteries as well as making it compatible with our new 400mah batteries that are 24mm wide. This new chassis kit comes with lateral CF braces to locate the battery side to side, but also to stiffen the front to back structure of the car for more precise handling and higher corner speeds. The kit is finished off with a new forward center shock mount that incorporates a band-less battery hold down that is more reliable and easier to use.

RX28-043

New G2 Turnbuckles with 2mm threads and double adjustment holes at 90* for easier toe in adjustment.

RX28-055

RX28-055-1

New G2 Ball Adjustable Upper arm replacements.

*Must use with RX28-044 2mm Turnbuckle set and/or RX28-042 2mm Ball Cups.

RX28-044

Replacement 2mm Turnbuckles and Ballcups to use with your RX28G2 FRP Adjustable Upper Arms. Must buy these to use the included arms in the RX28G2 kit.

RX28-042

New G2 Ball Cups made for 2mm threads.

**Must be used with the RX28A-33 Shock, New G2 Turnbuckles and Side Dampers.

RX28-057

Refresh Set of plastics for your RX28G2 Double A-Arm cars ( STD and SE).

Included:

-2x FRP Adjustable Upper Arms

-2x Damper Tubes

-2x Left Rear Wheel Nuts

-4x Wheel Nuts

-12x 2mm Ball Cups

RX28-058

Update Set of plastics for your RX28G2 Double A-Arm cars ( STD and SE).

Included:

-2x FRP Adjustable Upper Arms

-2x Damper Tubes

-2x Left Rear Wheel Nuts

-4x Wheel Nuts

-12x 2mm Ball Cups

-2x G2 Hardened Steel Adjustable Arm Turnbuckles

-2x G2 Hardened Steel Steering Turnbuckles

-2x G2 Damper Pistons

RX28K-KITG2 (New Old Stock) Never been opened and or used. Rare Find!

RX28SE-08

This all new chassis for your RX28SE Gen 2 changes the battery and shock mounting system slightly so that we can have more space to move the 340mah hardcase lipo fore and aft on the chassis, as well as allowing for our new 400mah LiHv battery to fit in the chassis in 98mm configuration. This chassis also sheds approximately 5-6g off of the chassis in higher areas ensuring that while the chassis gets lighter, the center of gravity does not suffer. The kit is finished off with a new forward center shock mount that incorporates a band-less battery hold down that is more reliable and easier to use.

RX28SE-07

RX28SE-03

RX28SE-02

RX502

This is the all new GL RGT Rear Geometry Conversion Kit. Developed in house this kit was designed with our numerous years of experience designing 1/12 and 1/10 Pan Cars. The shock mounting postions and angles have been revised, the center of gravity has been dropped and the parts count and complexity have been reduced considerably. Additionally the integrated rear body mount position is compatible with most lexan bodies we have tested. The results are a car that produces more rear grip, better steering and more consistent, predictable handling. Having removed the motor mount shock mount extension also allows for easier wire routing for smoother pod movement and better airflow for the motor to stay cool.

Lap time wise we have seen resonable improvement, and consistency has gone through the roof! The car is much more composed under power and tracks far straighter. As another benefit, the time in between rear damper maintenance has been increased.

This kit includes the rear cross brace the aluminum tri mount to be installed on the stock motor mount. It is compatible with both the GL GLR rear shocks and PN Racing Side Shocks.

Needed to Complete:

-When using GLR Parts:

*GLR-S005 Plastic Shocks

*GLR-S016 Alloy Adjusters

*GLR-S021 Pivot Balls

*2 x M2 x 4mm BH Screws

*2 x M2 x 6mm Set Screws

*GLR-003-S Spring Set

(*alternatively, using Atomic 3.5mm Ball Studs simplifies the parts count AMZ-OP023, use 4 pcs of these plus 2x M2 nuts)

-When Using PN Racing Parts

*MR2162A Spring Set

*MR2990

*4 x M2 x 8mm BH Machine Screws

*2 x M2 Nut

RX503

RX504