RX601W

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX601B

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RRE013

Charging cable used to connect to your usual white 3 pin battery connector charging cable to our new Reflex Racing 340mah LiHV hard case battery pack.

RX28-030

RX28A-33-MS

RX410

RX537

This V3 tool kit has an all new smooth handle finish and now includes a PH 00 Philips head screw driver that is more effective with the small pivot adjustment screws on the RX28. It comes with the necessary drivers to assemble your RX28. It is also compatible with most 1/28 scale car kits in the market today.

It includes:

Allen Drivers:

0.9mm

1.3mm

1.5mm

Nut Drivers:

4.0mm

4.5mm

Phillips Driver:

#0 (4mm)

#00 (2mm)

-1x M2x6 BH Screw (use M2x6 BH Screw plus M2 gold washer on top of top spring when installing 2 weights).

-1x M2 Gold Washer

-2x Black MD Spring (Soft)

-2x Silver MD Spring (Medium)

RX600R141Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit. The result is typically a little easier to drive car.

RX600R141G

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit. The result is typically a little easier to drive car.

RX600R141G

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit. The result is typically a little easier to drive car.

RX600R14Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R14W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R14G

RX600R3Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R3G

RX600R0Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R0W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.