RX28-059

Silver Horse Tire Management System Disc Organizer Set - Reflex Racing Version

Keep your wheel discs perfectly organized and ready for action with the Silver Horse Tire Management System Disc Organizer Set. Designed for serious racers who demand efficiency at the track, this two-piece organizer system transforms chaotic pit stops into streamlined tuning sessions.

Reflex Disc Holder Version - Each set includes two organizers that hold up to 20 Reflex wheel discs per organizer (40 discs total), providing dedicated storage for your entire Reflex disc collection.

Engineered to fit perfectly in the Silver Horse RC Tire Management System side compartment, these organizers integrate seamlessly with your existing tire management setup, maximizing your workspace efficiency and keeping all your tuning essentials in one centralized location.

No more fumbling through loose discs or wasting precious time searching for the right combination. With the Silver Horse organizer system, you can quickly identify and access the exact discs you need, allowing you to focus on what matters most: dialing in your tire setup and staying competitive.

Whether you're managing multiple tire compounds for changing track conditions or fine-tuning your wheel setup between heats, this organizer set keeps everything at your fingertips. Stay organized, save time, and gain the competitive edge that comes from efficient tire management.

Key Features:

• Set includes 2 organizers
  
• They stack in Organizer
• Reflex version: holds up to 40 Reflex wheel discs total
  
• Custom-fit design for Silver Horse RC Tire Management System side compartment
• Speeds up tire tuning and pit workflow

Also available for Nexx Wheels

** discs, wheels tires and tire management kit not included

This is a set of Full Ceramic Bearings for you 1/28 scale Pan Car.  Full Ceramic Bearings offer many benefits as outlined below:

1. Reduced Friction: They provide lower rolling resistance, which can improve the car's speed and overall efficiency.
   
2. Enhanced Durability: The wear-resistant nature of ceramic bearings means they can last longer under the high stress.
3. Lightweight: While not a lot, a full set of ceramics drops about 0.5g off your car.
   
4. Reduced Maintenance (somewhat): The low friction and wear properties eliminate the need for oil or grease. However, as our bearings have no races, they can allow more debris and tire dust to enter the bearings.
   
5. Corrosion Resistance: As they are not metallic, your bearings can be washed with something like dish soap and water.

RX28-045G2 (Black: Medium; Kit w/ 2 Upper & 2 Lower Arms, 4x Balls & 4x Screws)

RX607F125G

Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.

Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.

These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.

***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.

RX607F125W

Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.

Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.

These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.

***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.

RX607R125G

Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.

Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.

These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.

***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.

RX600R-15G

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The -1.5 1mm wheel was designed so we could use wider tires up front of our RX28s, while keeping the width up front with the equivalent of a +1 with 8.5mm wheels (in terms of the RX28). The negative offset- inset design reduces the scrub radius and makes the steering more precise. When using 11mm tires up front, we have found that the car is easier to drive and more consistent in modified, with smoother response and longer lasting tire life.

RX600R-15W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The -1.5 1mm wheel was designed so we could use wider tires up front of our RX28s, while keeping the width up front with the equivalent of a +1 with 8.5mm wheels (in terms of the RX28). The negative offset- inset design reduces the scrub radius and makes the steering more precise. When using 11mm tires up front, we have found that the car is easier to drive and more consistent in modified, with smoother response and longer lasting tire life.

RX600R-15Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The -1.5 1mm wheel was designed so we could use wider tires up front of our RX28s, while keeping the width up front with the equivalent of a +1 with 8.5mm wheels (in terms of the RX28). The negative offset- inset design reduces the scrub radius and makes the steering more precise. When using 11mm tires up front, we have found that the car is easier to drive and more consistent in modified, with smoother response and longer lasting tire life.

RX600F1G

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600F1W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600F1Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600F0G

RX600F0W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600F0Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R0G

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid

RX600R0W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.