RX532BL

The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.

The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.

RX532-BK

The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.

The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.

FX28-015 FX28 Steel Front Axles

Blue

The V2 Wing Things are designed to make mounting your wing much easier.  Install the screw from the bottom of the body and thread them into the wing thing threads.  You can hold the wing thing with a 4.0mm hex wrench to fully tighten.  Lighter and smaller than the V1 Set!

The V2 Wing Things are designed to make mounting your wing much easier.  Install the screw from the bottom of the body and thread them into the wing thing threads.  You can hold the wing thing with a 4.0mm hex wrench to fully tighten.  Lighter and smaller than the V1 Set!

RX601Y

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX601G

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX601W

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX601B

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX28-042

New G2 Ball Cups made for 2mm threads.

**Must be used with the RX28A-33 Shock, New G2 Turnbuckles and Side Dampers.

RX545

Replacement Spur Gear for your RX538 Gear Differential. The molded spur is a little bit tougher and longer lasting than the delrin machined version.

Link to Manual - https://www.reflexracing.net/assets/images/GearDiff_Manual.pdf?rdm=E9A4E1CA4AD2

**Please not the diff is not sealed at the bearings, so it is not designed to be "filled" with oil , but a healthy amount can be used when building. Left hub is not included.

RX603-30

All new from Reflex Racing is our brand new radial tires for RCP tracks. Through out testing in several spots across the USA we have found these tires to perform on par and often beyond the other offerings in the market. The feedback from both Pros and Joes is that these tires offer superior stability under rotation and great forward grip out of the corners.

The design of this tires was conceptualized so that the tire was not directional and instead of building a tread pattern on a slick, we actually cut into the slick to create a tread pattern. The result is a tread that flexes less for more stability under load and better exit traction. The compound was selected so that these tires still perform really well once the tread pattern has worn down well beyond being visible. In high traction conditions, this allows this tire to be used in smaller diameters, providing superior corner speed. Additionally we optimized the tire diameter for maximum corner speed and better rotation on the individual application. The 14mm tire is only 24.5mm in diameter, while the 11mm tire comes in at 25.25mm when mounted with super glue.

We recommend the 30 degree rear tires under most conditions. They work well in temps as low as 45 degrees (F) and perform well all the way into the 80's (F). If the grip is higher, simply cut the tire down smaller if you want a little more rotation in tight corners.

***Wheels are for picture only, they are not included***

RX602-30

All new from Reflex Racing is our brand new radial tires for RCP tracks. Through out testing in several spots across the USA we have found these tires to perform on par and often beyond the other offerings in the market. The feedback from both Pros and Joes is that these tires offer superior stability under rotation and great forward grip out of the corners.

The design of this tires was conceptualized so that the tire was not directional and instead of building a tread pattern on a slick, we actually cut into the slick to create a tread pattern. The result is a tread that flexes less for more stability under load and better exit traction. The compound was selected so that these tires still perform really well once the tread pattern has worn down well beyond being visible. In high traction conditions, this allows this tire to be used in smaller diameters, providing superior corner speed. Additionally we optimized the tire diameter for maximum corner speed and better rotation on the individual application. The 14mm tire is only 24.5mm in diameter, while the 11mm tire comes in at 25.25mm when mounted with super glue.

We recommend the 30 degree rear tires under most conditions. They work well in temps as low as 45 degrees (F) and perform well all the way into the 80's (F). If the grip is higher, simply cut the tire down smaller if you want a little more rotation in tight corners.

***Wheels are for picture only, they are not included***

RX28A-45 Reflex Racing RX28 Hard-Coated Aluminum Top Shock Shaft 

Shed some weight from up top for an even lighter CG.  This shaft sheds 0.3g from your top shock, leaving behind a 1.41g top shock.  When combined with the new aluminum turnbuckles, part no:  RX28A-44, it will shed 0.85g up top