RX551-BK Countersunk Washers - Black

FX28-036 Center Shock Adjustment Collar

RX607R125G

Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.

Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.

These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.

***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.

RX607F125W

Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.

Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.

These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.

***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.

RX607F125G

Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.

Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.

These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.

***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.

RX525

RX28-076 Gen 3 Upper Arm Hinge Pins

RX600R141Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit. The result is typically a little easier to drive car.

RX600R141G

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit. The result is typically a little easier to drive car.

RX600R141G

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit. The result is typically a little easier to drive car.

RX600R14Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R14W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R14G

RX600R3W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R3Y - 11mm Wheel

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R3G

RX600R0Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX600R0W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.