This part fits the following vehicles

• RC28 Team
• RC28R Team
• TC28

This part fits the following vehicles

• RC28 Team
• RC28R Team

This part fits the following vehicles

• RC28 Team
• RC28R Team

This part fits the following vehicles

• RC28 Team
• RC28R Team

28SRA Tech Table Multi-Inspection Tool

One tool, four checks, zero arguments at tech.

This is the gauge that keeps every pit stop honest — wing height, tire diameter, and body width, all in a single piece, precision laser cut from clear 1/4" acrylic and built to survive a season of trackside abuse.

What it checks:

• Wing Height — Stock Class: 45mm max
• Wing Height — Modified Class: 50mm max
• Body Width: 83mm max
• Tire Diameter: 25.5mm max

No calipers, no guesswork, no "close enough." Set the chassis against the tool, and it's pass or fail — same standard whether you're racing in Apex or on the other side of the planet.

One tool to rule them all, one ruleset to bind them — no borders, no exceptions.

NX-121 NEXX Racing Precision CNC 7075 Square Motor Mount for 90-94mm RM (SILVER)

NX-104 NEXX Racing Precision CNC 7075 Square Motor Mount for 90-94mm RM (ORANGE)

NX-103 NEXX Racing Precision CNC 7075 Square Motor Mount for 90-94mm RM (RED)

COLT End Bell — 30° Timing

Built for racers pushing boost and turbo timing setups, this end bell gives your ESC the extra room it needs to unlock that top-end pull. Same cast aluminum construction, same precision-bored center, same sealed bearing keeping your rotor spinning true, just dialed back to 30° to open up the timing window for setups that need it.

Fits both the COLT 25 (2500kv) and COLT 35 (3500kv), a drop-in swap, not a project. Comes with 3 new mounting screws, so you've got everything you need to bolt it on and go. If your ESC is calling for more timing space than stock allows, this is the end bell built to give it.

When your end bell takes a hit or just plain wears out, this is the replacement that gets you back on the track without missing a beat. Cast aluminum construction, precision-bored center, and a sealed bearing that keeps your rotor spinning true, race after race.

Built to factory spec, this end bell fits both the COLT 25 (2500kv) and COLT 35 (3500kv), a drop-in swap, not a project. Standard 40° timing, the setup most racers run stock. Bolt it on, plug it in, get back to business.

XL Power M2 4.0 Nylon Wheel Nut  - Black

PN Racing AAA Charging Tray Adapter w/ xt60 cable

GL Racing GL GT - Open, built, never run, servo included

ISDT N-Series N* Smart Charger - Pre-owned tested good

ISDT 608AC - pre-owned - tested

NEXX RACING V-line Front Suspension system is designed with innovative features such as quick adjustable caster, quick adjustable camber, adjustable ride height…. It makes the Mini-Z looks much like a real car, not only fast but also stable, better cornering and better suspension overall.  With locknuts and kingpins, V-LINE is designed to minimize most of the play resulting very smooth performance.  The V-LINE suspension systems fits only Mini-Z MR03 wide base models and also fits PN 2.5 Chassis.  For easy assembly, we pre-install the V-LINE suspension system at factory so it’s very easy and fast to assembly it on the Mini-Z.

COLOR: BLUE

V-LINE SUSPENSION SYSTEM FEATURES

• V- line suspension is designed with 2 V-shaped suspension forks to bring you a cool suspension system·
• Same width as stock. (MR02/ MR03 PNR2.5W Chassis width)·
• Suspension movement use ball joints instead of sliding knuckle and locknut easy adjustment play between knuckle and upper arm make joints will not pop out even during hard collision.·
• Adjustable camber from 0-3⁰ degrees with 4 position eccentric shaft with easy operation·
• Quick adjustable caster by caster bar from 0-1.9⁰ ·
• Both 0⁰ and 1⁰ lower A arms provided to facilitate suspension setup·
• Ride height adjustment  with turn of a screw·
• All 3 tie rods 0⁰, 0.5⁰, 1⁰ included ·
• High quality Precision CNC Swiss 7075 aluminum